![[PukiWiki]](http://www2.nao.ac.jp/~aste-www/aste_wiki/obs.jpg "[PukiWiki]")
[[Observing Log]] ---- #contents ---- * CSV2016: Preparations for radio pointing of DASH345/BAND8 (2016-09-02) [#t337e0ad] ** Tasks [#t9a581ab] - Preparations for radio pointing ---- ** Information [#be1346f2] - Observers: Kamazaki - Site: Mitaka - Weather conditions (2016-09-02T23:11) Temperature: -3.8 C Humidity: 0.75 hPa Wind: 16.3 m/s (245 deg) 220GHz opacity: 0.092 ** Pre-works [#ofb83c0a] *** Tuning at EL=60 deg. [#f3b8221c] [asteobs@aste-1c ~]$ swbox_ctl_be CONT [asteobs@aste-1c ~]$ swbox_ctl_be status: swbox_ctl_be CONT [asteobs@aste-1c ~]$ asterx_sw DASH345 [asteobs@aste-1c ~]$ synthe_ctl B FREQ 14.375 ### After setting synthe ### FREQ = 14.375000000 [GHz] AMPL = 20.00 [dBm] RF = ON [asteobs@aste-1c ~]$ asterx_set DASH345 ### Query of LO Freq ### LO Freq = 345.000000000 ### Set CLNA ### /cosmos3/naoj/bin/femc_ctl DASH345 CLNA_ON 345.000000000 vd0=1.200000, id0=10.000000 vd1=0.000000, id1=0.000000 vd2=0.000000, id2=0.000000 ASTE FEMC:OPEN FEMC_TCP 7 Ver 0.91 > Program running. Do not turn off power to CAN nodes. ---------- 45 4C 01 08 00 E1nd at Node index 00 AMBSI CAN Library V1.1.2 AMBSI Firmware V1.0.1 FEMC Firmware V2.5.0 FPGA V2.1.0 10 F2 B3 58 2 8 0 1B 1 A4 9A 4F 14 0 0 19 23 9B DE 4C 1 0 0 44 0 0 0 0 0 0 0 0 > SET_CLNA 0 1 1.20 10.00 0.00 0.00 0.00 0.00 OK > SET_CLNA 0 2 1.20 10.00 0.00 0.00 0.00 0.00 OK > SET_CLNA 1 1 1.20 10.00 0.00 0.00 0.00 0.00 OK > SET_CLNA 1 2 1.20 10.00 0.00 0.00 0.00 0.00 OK > GET_CLNA 0 1 1.205002,10.074158,-0.276947,0.003250,0.014343,4.910461,0.003693,0.023041,4.910461,1 > GET_CLNA 0 2 1.204865,10.044861,-0.380661,0.003220,0.023499,-4.848465,0.004120,0.022278,4.910446,1 > GET_CLNA 1 1 1.205994,10.052185,-0.794128,0.003189,0.022583,-4.882126,0.003326,0.024414,-4.881989,1 > GET_CLNA 1 2 1.206680,10.087738,-0.300400,0.003693,0.019073,-4.882095,0.003540,0.013275,4.931671,1 > CAN_CLOSE CAN closed ASTE FEMC:CLOSE ### Set SIS bias ### /cosmos3/naoj/bin/femc_ctl DASH345 SIS_ON 345.000000000 345.000000 1.900000 1.900000 1.900000 1.900000 ASTE FEMC:OPEN FEMC_TCP 7 Ver 0.91 > Program running. Do not turn off power to CAN nodes. ---------- 45 4C 01 08 00 E1nd at Node index 00 AMBSI CAN Library V1.1.2 AMBSI Firmware V1.0.1 FEMC Firmware V2.5.0 FPGA V2.1.0 10 F2 B3 58 2 8 0 1B 1 A4 9A 4F 14 0 0 19 23 9B DE 4C 1 0 0 44 0 0 0 0 0 0 0 0 > SET_SIS_MODE 0 SET SIS MODE:CLOSE LOOP > SET_SIS_V 0 1 1.900 OK > SET_SIS_V 0 2 1.900 OK > SET_SIS_V 1 1 1.900 OK > SET_SIS_V 1 2 1.900 OK > GET_SIS_VC 0 1 1.781921,5.468750 > GET_SIS_VC 0 2 1.784821,6.527710 > GET_SIS_VC 1 1 1.811066,28.860474 > GET_SIS_VC 1 2 1.818695,33.886719 > CAN_CLOSE CAN closed ASTE FEMC:CLOSE ### Set LO Power ### /cosmos3/naoj/bin/loatt_dash345_tune 345.000000000 /cosmos3/naoj/bin/loatt_dash345_val /home/astedev/frontend/loatt_ctl/loatt_dash345.conf 345.000000000 /cosmos3/naoj/bin/loatt_dash345 225 310 Set ATT : Pol0=225, Pol1=310 Pol0 = 225 , Pol1 = 310 Pol0 = 0.005490[A], Pol1 = 0.007567[A] Pol0 = 0.657290[V], Pol1 = 0.775379[V] [asteobs@aste-1c ~]$ swbox_ctl_pol 0 1 [asteobs@aste-1c ~]$ swbox_ctl_pol status: swbox_ctl_pol 0 1 400:P0-USB 402:P1-USB [asteobs@aste-1c ~]$ cont_if 2 22 changed Cont IF #2 att. = 22 [dB] Cont IF #2 Lev. = 0.000107 [V] [asteobs@aste-1c ~]$ cont_if 3 17 changed Cont IF #3 att. = 0 [dB] Cont IF #3 Lev. = -0.000349 [V] *** Pointing [#n6425782] - UT23:24 aste16/radpon/istx5d3.start az,el = -84 73 daz,del = 0.0 0.0 -> +4.0 0.0 dx,dy,dz,dtx,dty,dtz = all 0.0s *** OPT image check [#d0899eac] - UT23:33 aste16/radpon/t163-16C.start -- No response from aste-c1c -> power-cycle - [aste16@aste-ms1 ~]$ ssh astecntl@aste-c1c /cosmos3/naoj/sbinSol/optinit ssh_exchange_identification: read: Connection reset by peer - [asteobs@aste-1c ~]$ tap_lt1500.py lantap0 1 off POS=100,100,100,100 POF1 POS=000,100,100,100 (wait for 10 seconds) [asteobs@aste-1c ~]$ tap_lt1500.py lantap0 1 on POS=000,100,100,100 PON1 POS=100,100,100,100 - [aste16@aste-ms1 ~]$ ssh astecntl@aste-c1c /cosmos3/naoj/sbinSol/optinit device: [ ok ] mmap: [ ok ] init bcr: [ ok ] init: [ ok ] initLUT: [ ok ] clear FB: [ ok ] AVME-338B -> successfully initialized - [aste16@aste-ms1 ~]$ ~/analysis/bin/optshot.sh r 1 128 * image plane = r -> offset=0 * # of frames = 1 * frame capture delay = 1 (sec) * fov = blc(192, 192) - trc(319, 319) 001 [2016-09-02T23:45:09]: max,min,mean,sdev = 137 37 67.237 7.335 -rw-r--r-- 1 aste16 astgrp 16384 Sep 2 23:45 /var/tmp/opt_aste16.raw &ref(opt_20160902T2345.png); ** Radio pointing of DASH345 [#j69544ea] - UT23:33 aste16/radpon/istd3.list -- iOPT started at the same time - az,el = -88 68 daz,del = +4.0 0.0 dx,dy,dz,dtx,dty,dtz = all 0.0s - 2016/09/02 23:50:03 Temp. : -4.95 C Humid. : 17.70 % ( 0.75 hPa ) Solar : 0.00 kW/m2 Wind : 10.09 m/s 234 deg AirPressure : 570.03 hPa ( Rain: 0.01 ) Opacity @220 GHz : 0.0573 - Current time = 2016/09/02 23:50:05 Aspirin time = 2016/09/02 23:50:03 Weather time = 2016/09/02 23:49:54 Aspirin Offset : (Az, El) = ( 3.61, -11.91 ) Aspirin status : ** WIND ON ** ( C22:on C6:OFF WIND:on ) Refraction Corr. status : OK - UT23:53 - 00:00 the running observation paused due to sudden STBY in EL -- Recovered by just setting EL PROG again - UT00:27 aste-c1c down... 0903 00:27:38 SATURN 68.4 20.6 -24.4 7.2 -91.274 59.214 0.4 0.1 38 3 33 -0.5 0.9 0903 00:27:38 SATURN 65.3 21.7 -18.3 7.9 -91.274 59.214 -0.8 0.9 39 3 34 -0.6 0.9 Timeout, server not responding. [asteobs@aste-mx1 ~]$ ssh aste-c1c -l astecntl ssh_exchange_identification: read: Connection reset by peer - Power-cycle of aste-c1c - UT00:36 aste16/radpon/istd3.list restarted az,el = -92 57 daz,del = +4.0 0.0 - UT02:18 stopped 2016/09/03 02:13:21 Temp. : -7.29 C Humid. : 22.06 % ( 0.78 hPa ) Solar : 0.00 kW/m2 Wind : 9.18 m/s 256 deg AirPressure : 569.99 hPa ( Rain: 0.01 ) Opacity @220 GHz : 0.0595 - Current time = 2016/09/03 02:13:24 Aspirin time = 2016/09/03 02:13:23 Weather time = 2016/09/03 02:13:18 Aspirin Offset : (Az, El) = ( 4.33, -6.88 ) Aspirin status : ** WIND ON ** ( C22:on C6:OFF WIND:on ) Refraction Corr. status : OK
