[[Observing Log]]
----
#contents
----
* CSV2016: Beam maps of DASH345/BAND8 (2016-09-01) [#k938746b]
** Tasks [#a2599dd4]
- Beam maps of DASH345 and BAND8
- BAND8 investigation by Ito-san and Fujii-san between JST13:30 and 17:00
*** Preparations [#wf8bf9a6]
+ Basic checks
-- Record which kisa files are used for DASH345 and BAND8
+
aste16@aste-ms1: ssh astecntl@aste-1c "ls -l /cosmos3/aste/etc/kisag/{DASH3,BAND8}"
lrwxrwxrwx 1 astecntl astctl 12 Jun 3 2015 /cosmos3/aste/etc/kisag/BAND8 -> BAND8.150603
lrwxrwxrwx 1 astecntl astctl 12 Jun 1 2015 /cosmos3/aste/etc/kisag/DASH3 -> DASH3.150601
-- Check all subref parameters (dx,dy,dz,dtx,dty,dtz) are zero
-- Check Aspirin is working in the "WIND ON" mode
*** Beam maps in BAND8 [#ta9a2da7]
+ Tuning at EL=60.0 deg
-- [[Tuning of DASH345/BAND8 for continuum observations>CSV/2016#i6322df7]]
-- Don't forget to record weather conditions
+ Pointing toward Saturn
BAND8: stx5b8.start
+ Run the following observation tables one by one
BAND8: stb2xb8.start (1 map toward Saturn with x-direction scans)
BAND8: stb2yb8.start (1 map toward Saturn with y-direction scans)
*** Beam maps in DASH345 [#j3e633f6]
+ Tuning at EL=60.0 deg
-- [[Tuning of DASH345/BAND8 for continuum observations>CSV/2016#i6322df7]]
-- Don't forget to record weather conditions
+ Pointing toward Saturn
DASH345: stx5d3.start
+ Run the following observation tables one by one
DASH345: stb2xd3.start (1 map toward Saturn with x-direction scans)
DASH345: stb2yd3.start (1 map toward Saturn with y-direction scans)
+ Data reduction
-- Make maps every execution using cont
-- [[Beam map analysis>CSV/BeamMapMeasurementAnalysisSBRx#za235565]]
----
** Information [#t45948fe]
- Observers: Tanaka
- Site: Mitaka
- Weather conditions (2016-09-01Txx:xx)
Temperature: xxx C
Humidity: xxx hPa
Wind: xxx m/s (xxx deg)
220GHz opacity: xxx
** logs [#m08f5134]
- UT2340 restarting cosmos3 to restart aspirin
- tuning et al.
[asteobs@aste-1c ~]$ ls -lt /cosmos3/aste/etc/kisag/DASH3
lrwxrwxrwx 1 astecntl astctl 12 Jun 1 2015 /cosmos3/aste/etc/kisag/DASH3 -> DASH3.150601
[asteobs@aste-1c ~]$ ls -lt /cosmos3/aste/etc/kisag/BAND8
lrwxrwxrwx 1 astecntl astctl 12 Jun 3 2015 /cosmos3/aste/etc/kisag/BAND8 -> BAND8.150603
[asteobs@aste-1c ~]$ swbox_ctrl_be CONTW
-bash: swbox_ctrl_be: command not found
[asteobs@aste-1c ~]$ swbox_ctrl_be CONT
-bash: swbox_ctrl_be: command not found
[asteobs@aste-1c ~]$ swbox_ctl_be CONT
[asteobs@aste-1c ~]$ swbox_ctl_be
status: swbox_ctl_be CONT
[asteobs@aste-1c ~]$ asterx_sw BAND8
### SYNTHE RF-OFF ###
/cosmos3/naoj/bin/synthe_ctl B RF OFF
FREQ = 14.648764263 [GHz]
AMPL = 20.00 [dBm]
RF = ON
### After setting synthe ###
FREQ = 14.648764263 [GHz]
AMPL = 20.00 [dBm]
RF = OFF
### SWBOX changed ###
/cosmos3/naoj/bin/swbox_ctl_rx 1
### SYNTHE set ###
/cosmos3/naoj/bin/synthe_ctl B AMPL +13dBm
FREQ = 14.648764263 [GHz]
AMPL = 20.00 [dBm]
RF = OFF
### After setting synthe ###
FREQ = 14.648764263 [GHz]
AMPL = 13.00 [dBm]
RF = OFF
/cosmos3/naoj/bin/synthe_ctl B RF ON
FREQ = 14.648764263 [GHz]
AMPL = 13.00 [dBm]
RF = OFF
### After setting synthe ###
FREQ = 14.648764263 [GHz]
AMPL = 13.00 [dBm]
RF = ON
[asteobs@aste-1c ~]$ synthe_ctl B FREQ 11.444
FREQ = 14.648764263 [GHz]
AMPL = 13.00 [dBm]
RF = ON
### After setting synthe ###
FREQ = 11.444000000 [GHz]
AMPL = 13.00 [dBm]
RF = ON
[asteobs@aste-1c ~]$ asterx_set BAND8
### Query of LO Freq ###
LO Freq = 411.984000000
### Set CLNA ###
/cosmos3/naoj/bin/femc_ctl BAND8 CLNA_ON 411.984000000
vd0=0.650000, id0=5.000000
vd1=0.600000, id1=4.500000
vd2=0.600000, id2=4.500000
ASTE FEMC:OPEN
FEMC_TCP 8
Ver 0.91
>
Program running.
Do not turn off power to CAN nodes.
---------- 45 4C 01 08 00 E1nd at Node index 00
AMBSI CAN Library V1.1.2
AMBSI Firmware V1.0.1
FEMC Firmware V2.5.0
FPGA V2.1.0
10 F2 B3 58 2 8 0 1B
1 A4 9A 4F 14 0 0 19
23 9B DE 4C 1 0 0 44
0 0 0 0 0 0 0 0
> SET_CLNA 0 1 0.65 5.00 0.60 4.50 0.60 4.50
OK
> SET_CLNA 0 2 0.65 5.00 0.60 4.50 0.60 4.50
OK
> SET_CLNA 1 1 0.65 5.00 0.60 4.50 0.60 4.50
OK
> SET_CLNA 1 2 0.65 5.00 0.60 4.50 0.60 4.50
OK
> GET_CLNA 0 1
0.654648,5.029449,-0.174683,0.603989,4.534149,-0.196884,0.604599,4.548492,-0.203812,1
> GET_CLNA 0 2
0.653748,5.039368,-0.194504,0.604340,4.556122,-0.194885,0.604019,4.553528,-0.202194,1
> GET_CLNA 1 1
0.654083,5.036469,-0.182388,0.604202,4.546814,-0.209656,0.604248,4.521484,-0.270737,1
> GET_CLNA 1 2
0.654205,5.017700,-0.170197,0.604752,4.552002,-0.192963,0.604340,4.509125,-0.200165,1
> CAN_CLOSE
CAN closed
ASTE FEMC:CLOSE
### Set Electro-magnet ###
/cosmos3/naoj/bin/femc_ctl BAND8 MAG_ON 411.984000000
v=12.800000, 13.400000, 10.400000, 19.100000
ASTE FEMC:OPEN
FEMC_TCP 8
Ver 0.91
>
Program running.
Do not turn off power to CAN nodes.
---------- 45 4C 01 08 00 E1nd at Node index 00
AMBSI CAN Library V1.1.2
AMBSI Firmware V1.0.1
FEMC Firmware V2.5.0
FPGA V2.1.0
10 F2 B3 58 2 8 0 1B
1 A4 9A 4F 14 0 0 19
23 9B DE 4C 1 0 0 44
0 0 0 0 0 0 0 0
> ACT_DEMAG 0 1 30.00 1.00 100
OK
> ACT_DEMAG 0 2 30.00 1.00 100
OK
> ACT_DEMAG 1 1 30.00 1.00 100
OK
> ACT_DEMAG 1 2 30.00 1.00 100
OK
> SET_MAG_C 0 1 12.80
OK
> SET_MAG_C 0 2 13.40
OK
> SET_MAG_C 1 1 10.40
OK
> SET_MAG_C 1 2 19.10
OK
> GET_MAG_VC 0 1
0.168976,12.317657
> GET_MAG_VC 0 2
0.170563,12.915421
> GET_MAG_VC 1 1
0.137405,9.845352
> GET_MAG_VC 1 2
0.261597,18.736267
> CAN_CLOSE
CAN closed
ASTE FEMC:CLOSE
### Set SIS bias ###
/cosmos3/naoj/bin/femc_ctl BAND8 SIS_ON 411.984000000
411.984000 2.001608 2.049580 1.996820 1.957012
ASTE FEMC:OPEN
FEMC_TCP 8
Ver 0.91
>
Program running.
Do not turn off power to CAN nodes.
---------- 45 4C 01 08 00 E1nd at Node index 00
AMBSI CAN Library V1.1.2
AMBSI Firmware V1.0.1
FEMC Firmware V2.5.0
FPGA V2.1.0
10 F2 B3 58 2 8 0 1B
1 A4 9A 4F 14 0 0 19
23 9B DE 4C 1 0 0 44
0 0 0 0 0 0 0 0
> SET_SIS_MODE 0
SET SIS MODE:CLOSE LOOP
> SET_SIS_V 0 1 2.002
OK
> SET_SIS_V 0 2 2.050
OK
> SET_SIS_V 1 1 1.997
OK
> SET_SIS_V 1 2 1.957
OK
> GET_SIS_VC 0 1
1.905365,94.000244
> GET_SIS_VC 0 2
1.961365,78.558350
> GET_SIS_VC 1 1
1.913681,26.083374
> GET_SIS_VC 1 2
1.899796,977.078247
> CAN_CLOSE
CAN closed
ASTE FEMC:CLOSE
### Set LO Power ###
/cosmos3/naoj/bin/femc_ctl BAND8 WCA_ON 411.984000000
v=1.828200, -0.300000, 2.500000, -0.350000
ASTE FEMC:OPEN
FEMC_TCP 8
Ver 0.91
>
Program running.
Do not turn off power to CAN nodes.
---------- 45 4C 01 08 00 E1nd at Node index 00
AMBSI CAN Library V1.1.2
AMBSI Firmware V1.0.1
FEMC Firmware V2.5.0
FPGA V2.1.0
10 F2 B3 58 2 8 0 1B
1 A4 9A 4F 14 0 0 19
23 9B DE 4C 1 0 0 44
0 0 0 0 0 0 0 0
> SET_PA_VD 0 1.83
OK
> SET_PA_VG 0 -0.30
OK
> SET_PA_VD 1 2.50
OK
> SET_PA_VG 1 -0.35
OK
> GET_PA 0
2.966309,247.726440,-0.291138
> GET_PA 1
4.022522,257.614136,-0.345459
> CAN_CLOSE
CAN closed
ASTE FEMC:CLOSE
[asteobs@aste-1c ~]$ swbox_ctl_pol 1 0
[asteobs@aste-1c ~]$ swbox_ctl_pol
status: swbox_ctl_pol 1 0
400:P1-LSB 402:P0-LSB
[asteobs@aste-1c ~]$ cont_if 2 21
Cont IF #2 Att. = 22 [dB]
changed Cont IF #2 att. = 21 [dB]
recieved value = -3.75813000E-04
recieved value = -3.75813000E-04
Cont IF #2 Lev. = -0.000376 [V]
[asteobs@aste-1c ~]$ cont_if 3 23
Cont IF #3 Att. = 0 [dB]
changed Cont IF #3 att. = 0 [dB]
recieved value = -4.03712000E-04
recieved value = -4.03712000E-04
Cont IF #3 Lev. = -0.000404 [V]
[asteobs@aste-1c ~]$
** Beam maps in BAND8 [#s6e228ea]
- UT2356 stx5b8 (pointing) dAz, dEl = 0, 0
#ref(Screenshot.png,,70%)
-- Tsys 220 K ???
-- ch02 is <very> noisy (forgot to take screenshots orz.)
- UT0000 stb2xb8 (x scan) dAz, dEl = ???, ???
Temp. : -2.55 C Humid. : 8.76 % ( 0.44 hPa ) Solar : 0.00 kW/m2
Wind : 8.31 m/s 241 deg AirPressure : 571.79 hPa ( Rain: 0.01 )
Opacity @220 GHz : 0.0368
- UT0029 stx5b8 (pointing) dAz, dEl = ???, ???
- UT0034 stb2yb8 dAz, dEl = -0.3, 5.4
Temp. : -3.94 C Humid. : 10.31 % ( 0.47 hPa ) Solar : 0.00 kW/m2
Wind : 1.94 m/s 237 deg AirPressure : 572.18 hPa ( Rain: 0.01 )
Opacity @220 GHz : 0.0495
- UT0052 unstable signal during scans#6- @cycle#2. continue to observe
#ref(Screenshot-2.png,,70%)
#ref(Screenshot-3.png,,70%)
-- signal level@ch2 appears strange
- UT0105 checked the result of the y scan and found the data corrpused. restart stb2yb8
Temp. : -4.03 C Humid. : 10.02 % ( 0.45 hPa ) Solar : 0.00 kW/m2
Wind : 1.54 m/s 194 deg AirPressure : 572.30 hPa ( Rain: 0.01 )
Opacity @220 GHz : 0.0605
** Beam maps in DASH345 [#vb03b8d3]
- tuning
[asteobs@aste-1c ~]$ asterx_sw DASH345
### SYNTHE RF-OFF ###
/cosmos3/naoj/bin/synthe_ctl B RF OFF
FREQ = 11.444000000 [GHz]
AMPL = 13.00 [dBm]
RF = ON
### After setting synthe ###
FREQ = 11.444000000 [GHz]
AMPL = 13.00 [dBm]
RF = OFF
### SWBOX changed ###
/cosmos3/naoj/bin/swbox_ctl_rx 0
### SYNTHE set ###
/cosmos3/naoj/bin/synthe_ctl B AMPL +20dBm
FREQ = 11.444000000 [GHz]
AMPL = 13.00 [dBm]
RF = OFF
### After setting synthe ###
FREQ = 11.444000000 [GHz]
AMPL = 20.00 [dBm]
RF = OFF
/cosmos3/naoj/bin/synthe_ctl B RF ON
FREQ = 11.444000000 [GHz]
AMPL = 20.00 [dBm]
RF = OFF
### After setting synthe ###
FREQ = 11.444000000 [GHz]
AMPL = 20.00 [dBm]
RF = ON
[asteobs@aste-1c ~]$ asterx_set DASH345
### Query of LO Freq ###
LO Freq = 274.656000000
### Set CLNA ###
/cosmos3/naoj/bin/femc_ctl DASH345 CLNA_ON 274.656000000
error: Freq range [326,371], 274.656000
### Set SIS bias ###
/cosmos3/naoj/bin/femc_ctl DASH345 SIS_ON 274.656000000
error: Freq range [326,371], 274.656000
### Set LO Power ###
/cosmos3/naoj/bin/loatt_dash345_tune 274.656000000
/cosmos3/naoj/bin/loatt_dash345_val /home/astedev/frontend/loatt_ctl/loatt_dash345.conf 274.656000000
/cosmos3/naoj/bin/loatt_dash345 error: over range of frequency 274.656000
usage:loatt_dash345 -p0/-p1 [val]
[asteobs@aste-1c ~]$ swbox_cntl_pol 0 1
-bash: swbox_cntl_pol: command not found
[asteobs@aste-1c ~]$ swbox_ctl_pol 0 1
[asteobs@aste-1c ~]$ swbox_ctl_pol
status: swbox_ctl_pol 0 1
400:P0-USB 402:P1-USB
[asteobs@aste-1c ~]$
[asteobs@aste-1c ~]$ synthe_ctl B FREQ 14.375
FREQ = 11.444000000 [GHz]
AMPL = 20.00 [dBm]
RF = ON
### After setting synthe ###
FREQ = 14.375000000 [GHz]
AMPL = 20.00 [dBm]
RF = ON
[asteobs@aste-1c ~]$ asterx_set DASH345
### Query of LO Freq ###
LO Freq = 345.000000000
### Set CLNA ###
/cosmos3/naoj/bin/femc_ctl DASH345 CLNA_ON 345.000000000
vd0=1.200000, id0=10.000000
vd1=0.000000, id1=0.000000
vd2=0.000000, id2=0.000000
ASTE FEMC:OPEN
FEMC_TCP 7
Ver 0.91
>
Program running.
Do not turn off power to CAN nodes.
---------- 45 4C 01 08 00 E1nd at Node index 00
AMBSI CAN Library V1.1.2
AMBSI Firmware V1.0.1
FEMC Firmware V2.5.0
FPGA V2.1.0
10 F2 B3 58 2 8 0 1B
1 A4 9A 4F 14 0 0 19
23 9B DE 4C 1 0 0 44
0 0 0 0 0 0 0 0
> SET_CLNA 0 1 1.20 10.00 0.00 0.00 0.00 0.00
OK
> SET_CLNA 0 2 1.20 10.00 0.00 0.00 0.00 0.00
OK
> SET_CLNA 1 1 1.20 10.00 0.00 0.00 0.00 0.00
OK
> SET_CLNA 1 2 1.20 10.00 0.00 0.00 0.00 0.00
OK
> GET_CLNA 0 1
1.204865,10.052185,-0.279190,0.003281,0.012817,4.910309,0.003647,0.022125,4.910370,1
> GET_CLNA 0 2
1.204971,10.043793,-0.382202,0.003204,0.023804,-4.848450,0.004135,0.021515,4.910324,1
> GET_CLNA 1 1
1.206070,10.039520,-0.796738,0.003189,0.022125,-4.882141,0.003281,0.024719,-4.882019,1
> GET_CLNA 1 2
1.206680,10.092773,-0.302322,0.003769,0.019531,-4.882126,0.003464,0.013580,4.931671,1
> CAN_CLOSE
CAN closed
ASTE FEMC:CLOSE
### Set SIS bias ###
/cosmos3/naoj/bin/femc_ctl DASH345 SIS_ON 345.000000000
345.000000 1.900000 1.900000 1.900000 1.900000
ASTE FEMC:OPEN
FEMC_TCP 7
Ver 0.91
>
Program running.
Do not turn off power to CAN nodes.
---------- 45 4C 01 08 00 E1nd at Node index 00
AMBSI CAN Library V1.1.2
AMBSI Firmware V1.0.1
FEMC Firmware V2.5.0
FPGA V2.1.0
10 F2 B3 58 2 8 0 1B
1 A4 9A 4F 14 0 0 19
23 9B DE 4C 1 0 0 44
0 0 0 0 0 0 0 0
> SET_SIS_MODE 0
SET SIS MODE:CLOSE LOOP
> SET_SIS_V 0 1 1.900
OK
> SET_SIS_V 0 2 1.900
OK
> SET_SIS_V 1 1 1.900
OK
> SET_SIS_V 1 2 1.900
OK
> GET_SIS_VC 0 1
1.783142,5.957031
> GET_SIS_VC 0 2
1.784973,7.223511
> GET_SIS_VC 1 1
1.809845,28.799438
> GET_SIS_VC 1 2
1.814575,34.075928
> CAN_CLOSE
CAN closed
ASTE FEMC:CLOSE
### Set LO Power ###
/cosmos3/naoj/bin/loatt_dash345_tune 345.000000000
/cosmos3/naoj/bin/loatt_dash345_val /home/astedev/frontend/loatt_ctl/loatt_dash345.conf 345.000000000
/cosmos3/naoj/bin/loatt_dash345 225 310
Set ATT : Pol0=225, Pol1=310
Pol0 = 225 , Pol1 = 310
Pol0 = 0.005490[A], Pol1 = 0.007566[A]
Pol0 = 0.660220[V], Pol1 = 0.777468[V]
[asteobs@aste-1c ~]$ ccont_if 2 22
-bash: ccont_if: command not found
[asteobs@aste-1c ~]$ cont_if 2 22
Cont IF #2 Att. = 21 [dB]
changed Cont IF #2 att. = 22 [dB]
recieved value = -1.70267000E-04
recieved value = -1.70267000E-04
Cont IF #2 Lev. = -0.000170 [V]
[asteobs@aste-1c ~]$ cont_if 3 17
Cont IF #3 Att. = 0 [dB]
changed Cont IF #3 att. = 0 [dB]
recieved value = +1.05713000E-04
recieved value = +1.05713000E-04
Cont IF #3 Lev. = 0.000106 [V]
- UT0141 stx5d3 dAz, dEl = -0.3, 5.4
Temp. : -4.31 C Humid. : 10.08 % ( 0.45 hPa ) Solar : 0.00 kW/m2
Wind : 3.68 m/s 260 deg AirPressure : 572.26 hPa ( Rain: 0.01 )
Opacity @220 GHz : 0.0364
- UT0144 stb2xd3 dAz, dEl = 2.9, 4.0
- UT0212 stx5d3 dAz, dEl = 2.9, 4.0
- UT0216 stb2xd3 dAz, dEl = 0.8, 5.4
Temp. : -5.73 C Humid. : 10.81 % ( 0.43 hPa ) Solar : 0.00 kW/m2
Wind : 2.39 m/s 278 deg AirPressure : 572.13 hPa ( Rain: 0.01 )
Opacity @220 GHz : 0.0839
* results [#v531bbcb]
- Band8 beam maps (contour@every 5K)
- bmaj, bmin, bpa = 24".1 x 20".0, 14.0 deg
#ref(result1.png,,100%)
- DASH3 beam maps (contour@every 5K)
- bmaj, bmin, bpa = 25".9 x 22".3, 2.2 deg
#ref(result2.png,,100%)
* FMLO Commissioning [#m71bf1d0]
** Observing from ASTE site [#vd0f73a5]
- operator: ytamura
- contact: yoichi.tamura on skype
** OTF test (AI-5D) [#hef3e582]
- 14h10 UTC - tuning with mORmpx.start
[asteobs@aste-1c ~]$ asterx_set DASH345
### Set LO Power ###
/cosmos3/naoj/bin/loatt_dash345_tune 351.593590536
/cosmos3/naoj/bin/loatt_dash345_val /home/astedev/frontend/loatt_ctl/loatt_dash345.conf 351.593590536
/cosmos3/naoj/bin/loatt_dash345 292 286
Set ATT : Pol0=292, Pol1=286
Pol0 = 292 , Pol1 = 286
Pol0 = 0.007125[A], Pol1 = 0.006980[A]
Pol0 = 0.668527[V], Pol1 = 0.769158[V]
[asteobs@aste-1c ~]$ mmc1_rstop
[asteobs@aste-1c ~]$ ifeo_tune 1 0.030
volt=0.030000
E/O att. = 10 dB E/O att. = 10 dB IF level=0.080330
new E/O att. = 10 dB IF level=0.080005
new E/O att. = 12 dB IF level=0.047764
new E/O att. = 14 dB IF level=0.031058
new E/O att. = 16 dB IF level=0.021055
new E/O att. = 14 dB IF level=0.036951
14 dB 0.036951 V
[asteobs@aste-1c ~]$ ifeo_tune 2 0.050
volt=0.050000
E/O att. = 13 dB IF level=0.087859
new E/O att. = 13 dB IF level=0.088188
new E/O att. = 14 dB IF level=0.065418
new E/O att. = 15 dB IF level=0.051254
new E/O att. = 16 dB IF level=0.041978
new E/O att. = 15 dB IF level=0.057717
15 dB 0.057717 V
[asteobs@aste-1c ~]$ yfactor 1
E/O att. = 14 dB
E/O IF level = 0.015902 V
R=0.034361 V, Sky=0.015902 V, Y=3.346140 dB
3.346140
[asteobs@aste-1c ~]$ yfactor 2
E/O att. = 15 dB
E/O IF level = 0.031376 V
R=0.055569 V, Sky=0.031376 V, Y=2.482350 dB
2.482350
- start tuning again.
- 14:22 UTC - pointing with R Lep
-- aste16/fmlo16/mLPpng.start
-- az,el = -90, 39
-- Tsys(A1) = 252 K
-- Ta*(A1) = 0.5 K
-- conditions:
Temp. : 1.93 C Humid. : 6.45 % ( 0.45 hPa ) Solar : 0.77 kW/m2
Wind : 6.82 m/s 229 deg AirPressure : 572.44 hPa ( Rain: 0.01 )
Opacity @220 GHz : 0.0481
-- daz,del = +1, +6 ==> corrected
- 14:29 UTC - testing FMLO-OTF table
-- aste16/fmlo16/mORmpx.start
-- ERR invalid operand, integ_time=3432 ==> &color(red,){Oops, I forgot an integration time < 1001s is only allowed for a single scan.};
- 14:53 UTC - testing again
-- ==> Again, ERR invalid operand INTEG_TIME=1018
- 14:59 UTC - testing again
-- OK, this time the table goes well.
[aste16@aste-1x obstable]$ ../bin/mkfmotf.pl -v mORmpx.start mORmpx_.start
total integration time (sec) : 1220
total scan time (sec) : 742
total scan time (hr:min:sec) : 0:12:22
saved as : /home/aste16/fmlo16/obstable/workOtf /mORmpx.start
ready to copy -> scp -Cp /home/aste16/fmlo16/obstable/workOtf/mORmpx.start aste16@aste-1s:/export/obstable/aste16/fmlo16/obstable/
*** FMLO-OTF observations [#l1088268]
- 15:17 UTC - %% FMLO-OTF toward the center of Orion A (&color(red,){southern half}; of 10'x10' map) %%
-- aste16/fmlo16/mORmpx&color(red,){1};.start
--- the table was made with:
$ aobs
mORmpx1.start src: Ori-KL, (scn: fmlo_1pt_+30+00,) dev: Wide_DASH3_12COL
mORmpx_.start (src: Ori-KL,) scn: fm_otfx1_10m+30+00, (dev: Wide_DASH3_12COL)
$ fobs_mac mORmpx1.start mac_w3s3.fmp # THIS WAS WRONG!! SHOULD BE workFmlo/mORmpx1.start
$ mkfmotf.pl mORmpx1.start mORmpx_.start
total integration time (sec) : 1650
total scan time (sec) : 986
total scan time (hr:min:sec) : 0:16:26
saved as : /home/aste16/fmlo16/obstable/workOtf/mORmpx1.start
ready to copy -> scp -Cp /home/aste16/fmlo16/obstable/workOtf/mORmpx1.start aste16@aste-1s:/export/obstable/aste16/fmlo16/obstable/
-- az,el = -82, 31
-- conditions
Temp. : 3.27 C Humid. : 6.05 % ( 0.47 hPa ) Solar : 0.95 kW/m2
Wind : 8.05 m/s 239 deg AirPressure : 572.30 hPa ( Rain: 0.01 )
Opacity @220 GHz : 0.0491
-- Tsys(A1) = 282 K, Tsys(A3) = 282 K
-- &color(red,yellow){==> DO NOT USE THIS DATA!! This is NOT an FMLO table.};
- 15:35 UTC - %% FMLO-OTF toward the center of Orion A (&color(green,){northern half}; of 10'x10' map) %%
-- aste16/fmlo16/mORmpx&color(green,){1};.start
--- the table was made with:
$ aobs
mORmpx2.start src: Ori-KL, (scn: fmlo_1pt_+30+00,) dev: Wide_DASH3_12COL
mORmpx_.start (src: Ori-KL,) scn: fm_otfx2_10m+30+00, (dev: Wide_DASH3_12COL)
$ fobs_mac mORmpx2.start mac_w3s3.fmp # THIS WAS WRONG!! SHOULD BE workFmlo/mORmpx2.start
$ mkfmotf.pl mORmpx2.start mORmpx_.start
total integration time (sec) : 1650
total scan time (sec) : 986
total scan time (hr:min:sec) : 0:16:26
saved as : /home/aste16/fmlo16/obstable/workOtf/mORmpx2.start
ready to copy -> scp -Cp /home/aste16/fmlo16/obstable/workOtf/mORmpx2.start aste16@aste-1s:/export/obstable/aste16/fmlo16/obstable/
-- az,el = -84, 26
-- conditions
Temp. : 3.18 C Humid. : 6.85 % ( 0.53 hPa ) Solar : 0.97 kW/m2
Wind : 7.35 m/s 256 deg AirPressure : 572.21 hPa ( Rain: 0.01 )
Opacity @220 GHz : 0.0811
-- Tsys = 306 K (A1), 336 K (A3)
-- &color(red,yellow){==> DO NOT USE THIS DATA!! This is NOT an FMLO table.};
16:03 UTC - FMLO-OTF toward the center of Orion A (&color(red,){southern half}; of 10'x10' map)
-- aste16/fmlo16/mORmpx&color(red,){1};.start
--- the table was made with:
$ aobs
mORmpx1.start src: Ori-KL, (scn: fmlo_1pt_+30+00,) dev: Wide_DASH3_12COL
mORmpx_.start (src: Ori-KL,) scn: fm_otfx1_10m+30+00, (dev: Wide_DASH3_12COL)
$ fobs_mac workFmlo/mORmpx1.start mac_w3s3.fmp
$ mkfmotf.pl mORmpx1.start mORmpx_.start
total integration time (sec) : 1650
total scan time (sec) : 986
total scan time (hr:min:sec) : 0:16:26
saved as : /home/aste16/fmlo16/obstable/workOtf/mORmpx1.start
ready to copy -> scp -Cp /home/aste16/fmlo16/obstable/workOtf/mORmpx1.start aste16@aste-1s:/export/obstable/aste16/fmlo16/obstable/
-- Error!! TRIG_DELAY was 130 us, which is too small!
- 16:09 UTC - FMLO-OTF toward the center of Orion A (&color(red,){southern half}; of 10'x10' map)
-- aste16/fmlo16/mORmpx&color(red,){1};.start (TRIG_DELAY is set to %%3130 us.%% ==> the correct value was not applied.)
-- Oops, the error shows up again. Try to check the table and will update fobs..
- 16:13 UTC - FMLO-OTF toward the center of Orion A (&color(red,){southern half}; of 10'x10' map)
-- aste16/fmlo16/mORmpx&color(red,){1};.start (TRIG_DELAY is set to 3130 us.)
--- the table was made with:
$ aobs
mORmpx1.start src: Ori-KL, (scn: fmlo_1pt_+30+00,) dev: Wide_DASH3_12COL
mORmpx_.start (src: Ori-KL,) scn: fm_otfx1_10m+30+00, (dev: Wide_DASH3_12COL)
$ fobs_mac workFmlo/mORmpx1.start mac_w3s3.fmp
$ mkfmotf.pl mORmpx1.start mORmpx_.start
total integration time (sec) : 1650
total scan time (sec) : 986
total scan time (hr:min:sec) : 0:16:26
saved as : /home/aste16/fmlo16/obstable/workOtf/mORmpx1.start
ready to copy -> scp -Cp /home/aste16/fmlo16/obstable/workOtf/mORmpx1.start aste16@aste-1s:/export/obstable/aste16/fmlo16/obstable/
-- az,el = -88, 18
-- Tsys = 362 K (A1), 484 K (A3)
-- Conditions
Temp. : 4.18 C Humid. : 6.29 % ( 0.52 hPa ) Solar : 1.01 kW/m2
Wind : 8.86 m/s 255 deg AirPressure : 571.97 hPa ( Rain: 0.01 )
Opacity @220 GHz : 0.0320
-- Finally, the table looks working correctly!
- 16:32 UTC - finished. suspended the commissioning (for lunch).
-- parked at +180, 90 for Saito-san's work inside the cabin.
** Observing from SPdA [#b66ab81c]
- operator: Y. Tamura, A. Taniguchi
- contact: yoichi.tamura on skype
*** Check Y-factor [#s9ca081d]
[asteobs@aste-1c]$ yfactor 1
Execute /cosmos3/naoj/bin/ifeo 1
E/O att. = 14 dB
E/O IF level = 0.017941 V
R=0.035640 V, Sky=0.017941 V, Y=2.980910 dB
2.980910
- no problem
[asteobs@aste-1c]$ yfactor 2
Execute /cosmos3/naoj/bin/ifeo 2
E/O att. = 15 dB
E/O IF level = 0.034557 V
R=0.057104 V, Sky=0.034557 V, Y=2.181305 dB
2.181305
- not good, do not use A3 and A4 in analysis!
*** Observations for the aligned-FMP check [#r4bc7be8]
- 21:15 UTC - mFXbchf.list for the aligned-FMP check
-- aste16/fmlo16/mIRopt.list
--- incl. [mFXp30f, mFXp33f, mFXp34f, mFXp35f, mFXp22f]
-- TRIG_DELAY = +3130 (130+3000) us
-- Az, El = -175, 26
-- Tsys = 404 K (A1), 813 K (A3)
Temp. : 0.30 C Humid. : 10.56 % ( 0.66 hPa ) Solar : 0.17 kW/m2
Wind : 10.58 m/s 246 deg AirPressure : 570.75 hPa ( Rain: 0.01 )
Opacity @220 GHz : 0.0838
-- Tsys = 481 K (A1), 666 K (A3) in mFXp35f
-- &color(red,){22:24 UTC - observation stopped by the lost control priority (durin mFXp35f)};
-- 22:25 UTC - restart observation from mFXp35f
-- Tsys = 505 K (A1), 674 K (A3) in mFXp35f
![[PukiWiki]](http://www2.nao.ac.jp/~aste-www/aste_wiki/obs.jpg "[PukiWiki]")
